Part No. 890564 Form No. F022502A
Page 8 of 8
Will not vacuum or has poor vacuum perfor-
mance.
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Solution
Possible Cause
Problem
Clean debris bag. Shake bag clean or wash. Adjust
nozzle height. Check for hose kit cap. Unclog nozzle or
exhaust (see page 5). Allow air to feed with debris.
Dirty debris bag. Nozzle height set too high or too low.
Hose kit cap missing. Clogged nozzle or exhaust.
Excessive quantity of debris.
1818
1818
18
Engine Service and Warranty
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
20.120.1
20.120.1
20.1
2020
2020
20
BILLY GOAT INDUSTRIES INC.
1803 S JEFFERSON LEE'S SUMMIT, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Purchased
from
Purchase
Date
1919
1919
19
Serial Plate
Record your machine model, serial number
and date-of-purchase and where purchased
R
min
-1
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
Abnormal vibration.
Engine will not start.
Engine is locked, will not
pull over.
Engine problem.
Check gasoline. Connect spark plug wire. Clean or
replace air cleaner. Or contact a qualified service
person. Quick Disconnect not fully engaged.
Check impeller and replace if required. Check
Engine.
Loose or out of balance impeller or loose engine.
Out of gasoline. Bad or old gasoline. Spark Plug wire
disconnected. Dirty air cleaner.Safety Interlock engaged.
Contact an engine servicing dealer for engine
problems.
9. To reinstall impeller, use a new impeller bolt and lockwasher and use
exactly the same crankshaft impeller shim washers as were removed
during disassembly (unless they were damaged). Note:
your unit may
or may not have required the use of shim washers
.
10. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N
.
m)
(see item 51 on page 11).
IMPELLER REMOVAL continued
Date of
Service
Service Performed
MAINTENANCE HISTORY
Engine (See Engine Manual)
Check for excessive vibration
Clean Debris Bag
Check bag strap tightness
Inspect for loose parts
Maintenance Operation
Follow these hourly
maintenance intervals.
Maintenance Schedule
Inspect for worn or damaged parts
Every 5 hrs
or (Daily)
Every
Use
11. Reinstall engine and impeller onto housing in reverse order of
removal.
12. Before connecting spark plug wire, slowly pull engine starting
rope to insure that impeller rotates freely.
13. Reinstall spark plug wire.
17.217.2
17.217.2
17.2
17.117.1
17.117.1
17.1
MAINTENANCE continued
1717
1717
17
R
104 dB
(8 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals