Billy Goat QB1004 User Manual download pdf (Page 3)

Part No. 430316 Form No. F012203A

Page 3 of 12

For your safety and the safety of others, these

directions should be followed:

Use of Ear Protection is recommended while

operating this machine.

Do not operate this machine without first reading

owner's manual and engine manufacturer's manual.

Use of Eye and breathing protection is recom-

mended when using this machine, especially in

dry and dusty conditions.

GENERAL SAFETY

PACKING CHECKLIST

PUT OIL IN ENGINE BEFORE STARTING

Read all safety and operating instructions

before assembling or starting this unit.

ASSEMBLY

Your Billy Goat is shipped from the factory in one carton,

completely assembled except for the upper handle assembly,

handle brace, plate deflector and throttle control.

These items should be included in your carton. If

any of these parts are missing, contact your dealer.

Boxing Checklist

Denotes parts found in

Parts Bag Assembly

(shown on page 4).

Handle Upper

Assembly

400957

Check

Handle Brace

400951

·DO NOT place hands or feet inside air intake opening, near

exhaust outlet or near any moving parts.

·DO NOT start engine without deflector attached to exhaust outlet.

·DO NOT direct exhaust outlet toward any bystanders.

·DO NOT operate this equipment without first inspecting

work area.

·DO NOT operate this equipment during excessive vibration.

·DO NOT start engine without housing front plate attached.

·DO NOT operate this machine on slopes greater than 20%.

·DO NOT blow any hot or burning debris, or any toxic or

explosive material.

·DO NOT allow children to operate this equipment.

example). Finish installing the other side of the upper handle assembly using

screw (Item 17) and lock nut (Item 32).

2. Install front of handle brace (Item 30), to blower housing using

one screw (Item 17), one washer (Item 58) and one lock nut (item 32).

Install rear of handle brace (item 30) to upper handle vibration mounts using

two lock nuts (item 32). Hand tighten only. NOTE: 13 hp Honda models will

have an offset bracket (item 65) installed at the front of the housing. Connect

the handle brace (Item 30) to the bracket (Item 65) on 13 hp models.

3. Securely tighten all hardware listed above in steps 1 thru 2.

4. Remove four lock nuts from the front plate and use them to attach the front

wheel bracket (Item 27). Using spacer (Item 18), washer (Item 19), and Lock

Nut (Item 16) to attach Front wheel (Item 23) onto the front wheel bracket.

5. (QB1304HBW only) Your unit was shipped with the rear wheels removed.

To complete assembly of your unit you must remove the clip at each end of

the rear axle and slide the rear wheel onto the axle, leaving all spacers and

washers in place between the frame and wheel. Re-install the clip at the end

of the axle to secure the wheel in place.

6.Connect spark plug wire.

Parts Bag &

Literature Assy

430334

Parts Bag

& Literature

Assy

Check

Per Model

Check

Engine

Manual

Per Model

Briggs & Stratton

6.5 or 10 HP

Honda 5, 8, or 13 hp

Check

Wire Director

Mount 430391

Check

Front Exhaust

Director

430315 (8/10/13 hp)

430370 (5/6.5 hp)

Check

Bracket Front

Wheel 430270

Check

Front Wheel

430271

1.Install front exhaust wire loop(Item 55) across upper handle and

slide wire loop to lowest possible position on upper handle.

Install upper handle (Item 28), to preassembled lower handle

(item 29) by sliding the upper over and down the outside of the

lower handle. Pull recoil handle from the engine and place it

between rope guides (Item 13). Using screw (Item 22) & lock nut

(Item 32) to install upper handle to lower handle. NOTE: Install

rope guide on the left hand side for the Honda unit and right hand

side for the Briggs & Stratton unit (See fig below for the pictorial

Subaru 9 hp

Check

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

Billy Goat QB1004 User Manual Page 3

Comments to this Manuals

Related products and manuals for Engine Billy Goat QB1004